loading
LK9
SPROLINK
S180-LK9-001-01
Status de disponibilidade: | |
---|---|
Introduction
LK9 is an HDMI/DP/VGA wall plate with HDBaseT output. It sends HDMI, audio, bi-directional RS232 and IR signals up to 230ft/70m over a single Cat6/6a cable. It provides a RS232, IR in and out, audio embedded with VGA in front panel, users could switch sources with the front button or RS232 command. LED indicators show the status of each input.
There are 2 working modes for LK9, auto mode and manual mode. In auto mode, it will auto detect inputs, and switch to the latest connected source auto automatically. In manual mode, users have to switch to the connected source manually.
There is a micro USB connector in front panel, which could be used to update the firmware. RS232 port also available in back cover side. LK9 could be powered up by local supply or POC powered by remote receiver, there is an extra 24V power output if local power is not used.
Features
● HDMI1.4, HDCP1.4 compliant
● HDBaseTTM technology
● Use the privately-owned DDC Emulation technology, improved compatibility.
● Firmware could be updated by Micro-USB
● Support video resolution from 480P to 4K@60 4:2:0, support 3D video.
● Transmit 4K video up to 131ft/40m, 1080P video up to 230ft/70m with Cat6/6a cable
● Uncompressed video, bandwidth 10.2Gbps
● Support bi-directional IR and RS232 control signal
● Support audio embedded and de-embedded
● Support audio separate from video transmit up to 70m
● Bi-direction POC (power over cable) 24V, one power supply to power up both Tx and Rx
● Both side support POC on off switch
● Recommend to use CAT6/6a/7 cable, 70m cable resistance should be less than 10 Ohm
Panel Description
1. Power Indicator: Solid blue, transmitter is powered on; No light, transmitter is not powered
2. VGA IN: Connect to VGA source
3. Audio In: Connect to 3.5mm analog audio, this audio in will embedded to VGA.
4. IR IN: Connect an IR receiver, the IR signal received from this port will be sent out via HDBaseT receiver
5. RS232: Connect a serial RS232 signal here, this RS232 data will pass through to HDBaseT receiver.
6. HDBaseT Link Indicator:
a)Solid green, good signal quality from HDBaseT port;
b)Blink green, HDBaseT port is disconnected or not transmitting signal
c)No light, no signal is being received from the HDBaseT port
7. VGA Indicator:
a)Solid green, VGA source is connected
b)No light, there is no VGA source connected or VGA no signal.
8. Select Button: Used to switch among different inputs.
9. Service: Firmware update via micro USB port.
10. IR Out: Connect an IR emitter, the triggered IR signals are received from HDBaseT receiver
11. DP Indicator:
a)Solid green, DP source is connected
b)No light, there is no DP source connected or DP no signal.
12. DP IN : Connect to DP source here ex. Mac, PC, laptop.
13. HDMI Indicator:
a)Solid green, HDMI source is connected
b)No light, there is no HDMI source connected or HDMI no signal.
14. HDMI IN:Connect an HDMI source here ex. Blu-ray player, cable box, etc
1. HDBT OUT: Connect a cat6/6a cable from here to an RX-DV70EA receiver, it can receive POC power, do not provide POC power output.
2. RS232: The RS232 here is used to control the wall plate, like switch,resolution, and picture adjust.
3. Power: Power In and power out here, Middle pin is GND, out 24V in left, In 24V in right.
Connection and Installation
Note: When installing the wall plates, do not cover the vents. Doing so may result in damage to the product and/or area surrounding it and void the warranty.
EDID and audio Selection
D1 | D2 | D3 | D4 | Explain |
0 | 0 | AUTO EDID | ||
0 | 1 | 1080P/PCM | ||
1 | 0 | 4K@60 4:2:0/PCM | ||
1 | 1 | USER EDID | ||
TX Insert (AUDIO) | 0 | DVI IN(AUDIO) | ||
1 | AUDIO IN | |||
RX Extract (AUDIO) | 0 | AUDIO IN | ||
1 | DVI IN(AUDIO) |
Infrared(IR) Distribution
The EX range of HDBaseT products include multiple options for control and routing of IR.
IR Emitter - Included
Video Resolutions | |
Video | 4096x2160@24/25/30/50*/60Hz*, 3840x2160@24/25/30/50*/60Hz* (UHD), 2048x1080p, 1080p@23.98/24/25/29.97/30/50/59.94/60Hz, 1080i@50/59.94/60Hz, 720p@50/59.94/60Hz, 576p, 576i, 480p, 480i |
VESA | 2560x2048, 2560x1600, 2048x1536, 1920x1200, 1680x1050, 1600x1200, 1600x900,1440x900, 1400x1050, 1366x768, 1360x768, 1280x1024, 1280x800, 1280x768, 1152x768,1024x768, 800x600, 640x480 |
Color space | YCbCr, RGB |
Chroma Subsampling | 4:4:4, 4:2:2, 4:2:0 (UHD Only) |
Color Depth | 8-bit, 10-bit, 12-bit |
Audio | |
Formats | PCM 2Ch, LPCM 5.1, LPCM 7.1, Dolby Digital, DTS 5.1, Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio, Dolby Atmos |
Sample Rate | 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz |
Bit Rate | Up to 24-bit |
Distance | |
Cat5e/6@4K | Up to 115ft/35m |
Cat6a/7@4K | Up to 130ft/40m |
Cat5e/6@1080p | Up to 197ft/60m |
Cat6a/7@1080p | Up to 230ft/70m |
HDMI 4K | Up to 15ft/5m |
HDMI 1080p | Up to 30ft/10m |
Signal | |
Bandwidth | 10.2Gbps |
CEC | Yes |
HDCP | HDCP2.2 compliant |
Temperature | |
Operating | 32ºF~122ºF, or 0℃~50℃ |
Storage | -4ºF~140ºF, or -20℃~60℃ |
Humidity | 20 ~ 90% non-condensing |
Power | |
Consumption | 10.8W for pair |
Supply | Input: AC100-240V 50/60Hz, Output: DC24V 0.75A |
Other | |
Dimension HxWxD | 157x75x21mm |
Weight | 250g |
Certification | |
Power supply | CE, FCC, UL, RoHS, CCC |
Product | CE, FCC |
Introduction
LK9 is an HDMI/DP/VGA wall plate with HDBaseT output. It sends HDMI, audio, bi-directional RS232 and IR signals up to 230ft/70m over a single Cat6/6a cable. It provides a RS232, IR in and out, audio embedded with VGA in front panel, users could switch sources with the front button or RS232 command. LED indicators show the status of each input.
There are 2 working modes for LK9, auto mode and manual mode. In auto mode, it will auto detect inputs, and switch to the latest connected source auto automatically. In manual mode, users have to switch to the connected source manually.
There is a micro USB connector in front panel, which could be used to update the firmware. RS232 port also available in back cover side. LK9 could be powered up by local supply or POC powered by remote receiver, there is an extra 24V power output if local power is not used.
Features
● HDMI1.4, HDCP1.4 compliant
● HDBaseTTM technology
● Use the privately-owned DDC Emulation technology, improved compatibility.
● Firmware could be updated by Micro-USB
● Support video resolution from 480P to 4K@60 4:2:0, support 3D video.
● Transmit 4K video up to 131ft/40m, 1080P video up to 230ft/70m with Cat6/6a cable
● Uncompressed video, bandwidth 10.2Gbps
● Support bi-directional IR and RS232 control signal
● Support audio embedded and de-embedded
● Support audio separate from video transmit up to 70m
● Bi-direction POC (power over cable) 24V, one power supply to power up both Tx and Rx
● Both side support POC on off switch
● Recommend to use CAT6/6a/7 cable, 70m cable resistance should be less than 10 Ohm
Panel Description
1. Power Indicator: Solid blue, transmitter is powered on; No light, transmitter is not powered
2. VGA IN: Connect to VGA source
3. Audio In: Connect to 3.5mm analog audio, this audio in will embedded to VGA.
4. IR IN: Connect an IR receiver, the IR signal received from this port will be sent out via HDBaseT receiver
5. RS232: Connect a serial RS232 signal here, this RS232 data will pass through to HDBaseT receiver.
6. HDBaseT Link Indicator:
a)Solid green, good signal quality from HDBaseT port;
b)Blink green, HDBaseT port is disconnected or not transmitting signal
c)No light, no signal is being received from the HDBaseT port
7. VGA Indicator:
a)Solid green, VGA source is connected
b)No light, there is no VGA source connected or VGA no signal.
8. Select Button: Used to switch among different inputs.
9. Service: Firmware update via micro USB port.
10. IR Out: Connect an IR emitter, the triggered IR signals are received from HDBaseT receiver
11. DP Indicator:
a)Solid green, DP source is connected
b)No light, there is no DP source connected or DP no signal.
12. DP IN : Connect to DP source here ex. Mac, PC, laptop.
13. HDMI Indicator:
a)Solid green, HDMI source is connected
b)No light, there is no HDMI source connected or HDMI no signal.
14. HDMI IN:Connect an HDMI source here ex. Blu-ray player, cable box, etc
1. HDBT OUT: Connect a cat6/6a cable from here to an RX-DV70EA receiver, it can receive POC power, do not provide POC power output.
2. RS232: The RS232 here is used to control the wall plate, like switch,resolution, and picture adjust.
3. Power: Power In and power out here, Middle pin is GND, out 24V in left, In 24V in right.
Connection and Installation
Note: When installing the wall plates, do not cover the vents. Doing so may result in damage to the product and/or area surrounding it and void the warranty.
EDID and audio Selection
D1 | D2 | D3 | D4 | Explain |
0 | 0 | AUTO EDID | ||
0 | 1 | 1080P/PCM | ||
1 | 0 | 4K@60 4:2:0/PCM | ||
1 | 1 | USER EDID | ||
TX Insert (AUDIO) | 0 | DVI IN(AUDIO) | ||
1 | AUDIO IN | |||
RX Extract (AUDIO) | 0 | AUDIO IN | ||
1 | DVI IN(AUDIO) |
Infrared(IR) Distribution
The EX range of HDBaseT products include multiple options for control and routing of IR.
IR Emitter - Included
Video Resolutions | |
Video | 4096x2160@24/25/30/50*/60Hz*, 3840x2160@24/25/30/50*/60Hz* (UHD), 2048x1080p, 1080p@23.98/24/25/29.97/30/50/59.94/60Hz, 1080i@50/59.94/60Hz, 720p@50/59.94/60Hz, 576p, 576i, 480p, 480i |
VESA | 2560x2048, 2560x1600, 2048x1536, 1920x1200, 1680x1050, 1600x1200, 1600x900,1440x900, 1400x1050, 1366x768, 1360x768, 1280x1024, 1280x800, 1280x768, 1152x768,1024x768, 800x600, 640x480 |
Color space | YCbCr, RGB |
Chroma Subsampling | 4:4:4, 4:2:2, 4:2:0 (UHD Only) |
Color Depth | 8-bit, 10-bit, 12-bit |
Audio | |
Formats | PCM 2Ch, LPCM 5.1, LPCM 7.1, Dolby Digital, DTS 5.1, Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio, Dolby Atmos |
Sample Rate | 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz |
Bit Rate | Up to 24-bit |
Distance | |
Cat5e/6@4K | Up to 115ft/35m |
Cat6a/7@4K | Up to 130ft/40m |
Cat5e/6@1080p | Up to 197ft/60m |
Cat6a/7@1080p | Up to 230ft/70m |
HDMI 4K | Up to 15ft/5m |
HDMI 1080p | Up to 30ft/10m |
Signal | |
Bandwidth | 10.2Gbps |
CEC | Yes |
HDCP | HDCP2.2 compliant |
Temperature | |
Operating | 32ºF~122ºF, or 0℃~50℃ |
Storage | -4ºF~140ºF, or -20℃~60℃ |
Humidity | 20 ~ 90% non-condensing |
Power | |
Consumption | 10.8W for pair |
Supply | Input: AC100-240V 50/60Hz, Output: DC24V 0.75A |
Other | |
Dimension HxWxD | 157x75x21mm |
Weight | 250g |
Certification | |
Power supply | CE, FCC, UL, RoHS, CCC |
Product | CE, FCC |